電蒸汽鍋爐點火運行前應對供熱系統進行調節，下面濟南盛鑫鍋爐的有關技術人員就給大家介紹一下供熱系統的調節方法。
1、電蒸汽鍋爐加水，打開補水閥門，將鍋爐注水至正常水位，然后關閉補水閥門。打開系統補水管閥門進行加水，并觀察各自動排氣情況，直到排氣閥不排氣為止，然后關閉加水閥門。
Electric steam boiler, add water, open water valves, boiler water to the normal water level, and then close the water valve. Open the system fill with water pipe valves and automatic exhaust situation observed until the exhaust vent is not far, and then close the valve with water.
2、電蒸汽鍋爐與系統加完水后通過控制箱設定水泵低溫運轉，開泵前除加水閥門不開外所有閥門均開啟，還應打開啟閉器液壓管排氣閥排氣。此時應觀察鍋爐水位，如水位上升，則應適當關小阻力調節閥，直到鍋爐水位不升為止：如水位下降，證明系統水不滿，應繼續往鍋爐補水，直到水位不降為止。
Electric steam boiler and system after adding water pump cryogenic operation by setting the control box, before adding water pump in addition to the valve does away all valves are open, but also opens the exhaust valve opening and closing hydraulic pipe exhaust. You should observe the boiler water level, such as the water level rises, off a small resistance should be appropriate to adjust the valve until the boiler water level does not rise so far: If the water level drops, water proof system discontent, should continue to boiler feed water, until the water level does not drop so far.
3、電蒸汽鍋爐水位調整正常后，關閉水泵，檢查啟閉器，止回閥是否正常。檢查的方法是看鍋爐水位是否上升，如上升，證明有關閉不嚴的地方，可耳附在啟閉器和止回閥上聽，如關閉不嚴則會(huì )聽到“嚓嚓”的水流聲，如是啟閉器的問題請按其說明書處理，如是啟回閥的問題，應拆下檢查活門是否靈活，閥里是否有異物卡住。
Electric steam boiler water level adjusted properly, turn off the pump, check the hoist, a check valve is normal. Way to check is to see if the boiler water level rises, such as rise, proved lax closed places, listening ear attached to the hoist and check valves, such as closed lax will hear "Cha Cha" sound of water , the case of the opening and closing its manual handling problems,please problems in the case of Kai-return valve, remove the check valves is flexible, if there is a valve in the foreign body stuck.
