燃油蒸汽鍋爐采用水管貫流式爐膽結構，并配備安全閥，溫度過熱，水位過低，壓力過高等四重保護，絕對安全可靠。燃油蒸汽鍋爐操作簡單，只需按下按鈕，既進入自動運行狀態，無需專人值守。但是它也會有出現故障的時候，那么在平時的使用中，應該注意些什么呢？
1、使用蒸汽鍋爐應特別注意鍋爐房的通風條件，萬一發生泄漏，如果通風不好的話，極易引起液態氣在地面上凝結和擴散，造成惡性爆炸事故。
Special attention should be using the steam boiler boiler room ventilation, if leaks occur if ventilation is not good, can easily cause condensation of liquid gas in the ground and spread vicious explosion.
2、鍋爐人員應時刻注意氣體閥門的開關情況。氣體管路不可漏氣，若有異常情況，如鍋爐房內有異常氣味，不可開啟燃燒器，應及時檢查通風情況，排除氣味，檢查閥門，正常后才可投入運行。
Boiler should always pay attention to the situation of gas valve switch. Gas pipeline can not leak, if unusual circumstances, such as the boiler room abnormal odor, not open burners, ventilation should be checked to exclude odor, check valves, to get ready for normal operation after.
3、氣體壓力不可過高和過低，應在設定的范圍內運行，具體參數由蒸汽鍋爐生產廠家提供。當鍋爐運行一段時間，發現氣體壓力低于設定值時，應及時與煤氣公司聯系，供氣壓力是否有變化。燃燒器運行一段時間，應及時檢查管路中過濾器是否清潔，如氣壓下降很多，有可能是氣體雜質過多，過濾器被堵塞，應拆下清洗，必要時更換濾芯。
Gas pressure is not too high and too low, should operate within a set range, specific parameters provided by the steam boiler manufacturer. When the boiler is running for some time, found that the gas pressure is lower than the set value, it is timely contact with the gas company, if there is change in air pressure. Burner running for some time, should be checked in the pipeline filter is clean, like a lot of pressure decline, there may be too much gas impurities, the filter is clogged, remove the cleaning, replace the filter when necessary.
4、在停運一段時間或檢查管路后，在重新投入運行時，應打開放空閥，放氣一段時間，放氣時間應根據管路長短及氣體種類來確定。若鍋爐停用時間較長，則應切斷煤氣供應總閥，關閉放空閥。
After the outage or check the pipeline for some time, when put into operation again, open the vent valve, bleed for some time, deflated time should be determined according to the length and type of gas pipeline. If the boiler is disabled longer time, you should cut off the gas supply valve, close the vent valve.
